dmesg:
CPU revision is: 00024000 Enabling BCM4710A0 cache workarounds. Primary instruction cache 8kB, physically tagged, 2-way, linesize 16 bytes. Primary data cache 4kB, 2-way, linesize 16 bytes. Linux version 2.4.30 (nbd@ux-2y02) (gcc version 3.4.4 (OpenWrt-1.0)) #1 Sun Mar 26 19:02:04 CEST 2006 Setting the PFC value as 0x15 Determined physical RAM map: memory: 01000000 @ 00000000 (usable) On node 0 totalpages: 4096 zone(0): 4096 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 init=/etc/preinit noinitrd console=ttyS0,115200 CPU: BCM4710 rev 0 at 125 MHz Using 62.400 MHz high precision timer. !unable to setup serial console! Calibrating delay loop... 82.94 BogoMIPS Memory: 14268k/16384k available (1412k kernel code, 2116k reserved, 100k data, 80k init, 0k highmem) Dentry cache hash table entries: 2048 (order: 2, 16384 bytes) Inode cache hash table entries: 1024 (order: 1, 8192 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 1024 (order: 0, 4096 bytes) Page-cache hash table entries: 4096 (order: 2, 16384 bytes) Checking for 'wait' instruction... unavailable. POSIX conformance testing by UNIFIX PCI: Fixing up bus 0 PCI: Fixing up bridge PCI: Setting latency timer of device 01:00.0 to 64 PCI: Fixing up bus 1 Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd devfs: v1.12c (20020818) Richard Gooch ([email protected]) devfs: boot_options: 0x1 JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB. Squashfs 2.1-r2 (released 2004/12/15) (C) 2002-2004 Phillip Lougher pty: 256 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled b44.c:v0.93 (Mar, 2004) PCI: Setting latency timer of device 00:02.0 to 64 eth0: Broadcom 47xx 10/100BaseT Ethernet 00:11:2f:7d:85:4a PCI: Setting latency timer of device 00:08.0 to 64 eth1: Broadcom 47xx 10/100BaseT Ethernet 00:11:2f:7d:85:4a Amd/Fujitsu Extended Query Table v1.1 at 0x0040 Physically mapped flash: Swapping erase regions for broken CFI table. number of CFI chips: 1 cfi_cmdset_0002: Disabling fast programming due to code brokenness. Flash device: 0x400000 at 0x1fc00000 Creating 5 MTD partitions on "Physically mapped flash": 0x00000000-0x00040000 : "pmon" 0x00040000-0x003f0000 : "linux" 0x000bc400-0x002b1000 : "rootfs" mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only 0x003f0000-0x00400000 : "nvram" 0x002c0000-0x003f0000 : "OpenWrt" Initializing Cryptographic API NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 1024 bind 2048) ip_conntrack version 2.1 (5953 buckets, 5953 max) - 328 bytes per conntrack ip_tables: (C) 2000-2002 Netfilter core team NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. NET4: Ethernet Bridge 008 for NET4.0 802.1Q VLAN Support v1.8 Ben GreearAll bugs added by David S. Miller VFS: Mounted root (squashfs filesystem) readonly. Mounted devfs on /dev Freeing unused kernel memory: 80k freed Warning: unable to open an initial console. Algorithmics/MIPS FPU Emulator v1.5 diag boardtype: 0000041a Probing device eth0: No Robo switch in managed mode found Probing device eth1: No Robo switch in managed mode found Probing device eth2: No such device Probing device eth3: No such device BFL_ENETADM not set in boardflags. Use force=1 to ignore. b44: eth1: Link is up at 100 Mbps, full duplex. b44: eth1: Flow control is off for TX and off for RX. jffs2.bbc: SIZE compression mode activated. PCI: Setting latency timer of device 01:02.0 to 64 PCI: Enabling device 01:02.0 (0004 -> 0006) eth2: Broadcom BCM4320 802.11 Wireless Controller 3.90.37.0 Universal TUN/TAP device driver 1.5 (C)1999-2002 Maxim Krasnyansky Probing device eth0: No Robo switch in managed mode found Probing device eth1: No Robo switch in managed mode found Probing device eth2: [switch-robo.c:90] SIOCGETCPHYRD failed! [switch-robo.c:90] SIOCGETCPHYRD failed! No Robo switch in managed mode found Probing device eth3: No such device BFL_ENETADM not set in boardflags. Use force=1 to ignore. device eth0 entered promiscuous mode device eth1 entered promiscuous mode device eth2 entered promiscuous mode eth2: attempt to add interface with same source address. br0: port 2(eth2) entering listening state br0: port 1(eth1) entering listening state br0: port 2(eth2) entering learning state br0: port 1(eth1) entering learning state br0: port 2(eth2) entering forwarding state br0: topology change detected, propagating br0: port 1(eth1) entering forwarding state br0: topology change detected, propagating br0: port 1(eth1) entering disabled state b44: eth1: Link is up at 100 Mbps, full duplex. b44: eth1: Flow control is off for TX and off for RX. br0: port 1(eth1) entering listening state br0: port 1(eth1) entering learning state br0: port 1(eth1) entering forwarding state br0: topology change detected, propagating
nvram:
size: 2870 bytes (29898 left) acc_num=0 autofw_port0= boardnum=asusX boardtype=bcm94710dev boot_wait=on clkfreq=125 console_loglevel=1 dev_status=5 dhcp_domain=wan dhcp_enable=1 dhcp_end=192.168.1.150 dhcp_start=192.168.1.100 dhcp_wins=wan dl_ram_addr=a0001000 dmz_ipaddr= et0macaddr=00:11:2F:7D:85:4A et0mdcport=0 et0phyaddr=0 et1macaddr=00:11:2F:7D:85:4A et1mdcport=1 et1phyaddr=01 filter_client0= filter_maclist= filter_macmode=deny forward_port0= fsckpart= fw_disable=0 hardware_version=WL300-02-03-01-20 http_lanport=80 http_passwd=admin http_username= http_wanport= ide_device=105a: isformat=0 lan_domain= lan_hwaddr= lan_hwnames= lan_ifname=br0 lan_ifnames=eth1 eth2 lan_ipaddr=192.168.1.220 lan_lease=86400 lan_netmask=255.255.255.0 lan_proto=static lan_proto_x=1 lan_stp=1 lan_wins= log_ipaddr= log_level=0 ntp_server=192.5.41.40 192.5.41.41 133.100.9.2 os_date=Aug 4 2004 os_flash_addr=bfc40000 os_name=linux os_ram_addr=80001000 os_server= os_version=3.31.12.0 password=admin pmon_ver=PMON 3.11.19.0 productid=WLHDD regulation_domain=0X30DE rescueflag=disable restore_defaults=0 restore_defaults=0 router_disable=1 scratch=a0180000 sdram_config=0x0000 sdram_init=0x0419 sdram_ncdl=0x00000000 sdram_refresh=0x8040 sh_name= sh_num=0 sh_path= sh_rright= sh_rright_x= sh_wright= sh_wright_x= shutdown_hit=0 st_ftp_mode=1 st_max_user=6 st_model_t= st_name=WL-HDD st_part1= st_part2= st_part3= st_part4= st_part_t= st_partall= st_samba_mode=1 st_samba_workgroup=mygroup st_status_t=No HDD mounted stats_server= time_zone=UCT0 timer_interval=3600 upnp_enable=0 usb_available=1 usb_tmp_index=1:(null):add username=admin wan_desc= wan_device=vlan1 wan_dns= wan_domain= wan_gateway=0.0.0.0 wan_hostname= wan_hwaddr= wan_hwname= wan_ifname=eth1 wan_ifnames= wan_ipaddr=0.0.0.0 wan_lease=86400 wan_netmask=0.0.0.0 wan_pppoe_ac= wan_pppoe_demand=0 wan_pppoe_idletime=60 wan_pppoe_ifname= wan_pppoe_keepalive=0 wan_pppoe_mru=1492 wan_pppoe_mtu=1492 wan_pppoe_passwd= wan_pppoe_service= wan_pppoe_username= wan_primary=0 wan_proto=dhcp wan_route= wan_unit=0 wan_wins= watchdog=3000 wl0_ifname=eth2 wl0_infra=1 wl0_mode=ap wl0_radio=1 wl0_ssid=OpenWrt wl_antdiv=-1 wl_auth=0 wl_auth_mode=disabled wl_authmode_x=0 wl_bcn=100 wl_channel=0 wl_closed=0 wl_corerev= wl_country= wl_dtim=3 wl_frag=2346 wl_frameburst=off wl_frameburst_x=0 wl_gmode=1 wl_gmode_protection=auto wl_hwaddr= wl_ifname= wl_infra=1 wl_key1= wl_key2= wl_key3= wl_key4= wl_key=1 wl_lazywds=0 wl_maclist= wl_maclist_num_x=0 wl_macmode=disabled wl_macmode_x=0 wl_mode=ap wl_phytype=b wl_phytypes= wl_plcphdr=long wl_radio=1 wl_radioids= wl_radius_ipaddr= wl_radius_key= wl_radius_port=1812 wl_rate=0 wl_rateset=default wl_rateset_x=1 wl_rts=2347 wl_ssid=WL-HDD wl_unit=0 wl_wds= wl_wds_num_x=0 wl_wdsapply_x=1 wl_wdsmode_x=0 wl_wep=off wl_weptype_x=0 wl_wpa_gtk_rekey=0 wl_wpa_psk= wlp_beap_x=1 wlp_clientmode_x=1 wlp_num=0 wlp_pref_x=99